Der Markt; alle Pre-War fahrzeuge zu verkaufen

Überblick ähnlicher Anzeigen Morris Eight engine head pre 1938

  • Rover engine-s (and parts) for Rover

    Rover engine-s (and parts) for Rover

    16hp 6 cylinder engine for a Rover. Date stamping 30/8/32. (not sure of last digit). Casting N° 9680. Complete but minus pushrod-cover, carburettor and waterpump. Starter has light damage. Seized from very long standing, but was always dry-stored. Location: OS 53C
  • Morris axles front for Morris

    Morris axles front for Morris

    Front axle for ca. 1937 Morris Eight. In serviceable condition but brakes incomplete. (backing-plates only). Stamped number 73668, also 192. 530mm axle pads centres 669mm spring eye centres 973mm king pin approx. measured at top Location: AS 5
  • Morris doors (and door parts) for Morris

    Morris doors (and door parts) for Morris

    Pair of front doors for a circa 1937 Morris Eight Saloon. Good honest condition, only relatively minor welding in bottom corners required. Location: PS 1 2A
  • Citroën engine-s (and parts) for Citroën

    Citroën engine-s (and parts) for Citroën

    Differential-cover with oil-filling-plug (Part N° 2-39889)for the types C2/C3 Citroens 5CV. In very good condition, no cracks. Height 26cms, width 19cms.
  • Dodge engine-s (and parts) for Dodge

    Dodge engine-s (and parts) for Dodge

    Camshaft for a circa 1929 Dodge-DA 6 cylinder in very good condition.
  • Citroën engine-s (and parts) for Citroën

    Citroën engine-s (and parts) for Citroën

    Gearbox cover with shifter and original oil-filler-screw (part N° 2950). (Couvercle de la boîte de vitesses, avec levier de changement complet et bouchon de vidange). In very good condition, no chips or cracks. Top of cover would benefit from some smoothing off.
  • Morris axles front for Morris

    Morris axles front for Morris

    Set of new-old-stock king-pins and bushes for a Morris-Ten. Including two extra brass bushes, 1 ¼ inch long. These will not fit on Morris-Eight. pin diameter: 19mm / 99.2mm long brash bush OD: 22.85mm / 32mm long steel bush (brass lined): 22.85mm / 25mm long Location: UT HG 6B
  • Austin engine-s (and parts) for Austin

    Austin engine-s (and parts) for Austin

    Circa 1928 inlet manifold for Austin Seven. In good condition. Part N° 1A88.
  • Austin engine-s (and parts) for Austin

    Austin engine-s (and parts) for Austin

    Crankshaft for a circa 1928 Austin Seven. Marked 8969 and 1A4UA (part N°) and 92154. In good condition.
  • Vauxhall engine-s (and parts) for Vauxhall

    Vauxhall engine-s (and parts) for Vauxhall

    Nicely polished cast-aluminium tappet-cover for the 1926-1928 Vauxhall 20/60hp (T75). Length at top 70cms. Location: UT HG W: 3.8 L: 80

Ausgewählt

Riley 14/6 Special 1933
Riley 14/6 Special 1933
The ExperienceStep into the golden age of British motoring. This 1933 Riley 14/6 Special is a masterclass in pre-w..
Weiterlesen
1914 Brasier
1914 Brasier
1914 Brasier Tourer 9ABrasier were a French manufacturer who were in business from 1901 until 1930, when the company became victim of the gr..
Weiterlesen
1934 Chevrolet Standard Roadster
1934 Chevrolet Standard Roadster
1934 Chevrolet Standard Roadster This vehicle was delivered to Australia from Chevrolet and the body was manufactured by Holden Body Works w..
Weiterlesen